Rot occurs whenever water gets into cracks or penetrates a wood finish and can't dry out. Seal these cracks and maintain the finish to protect wood's beauty and integrity. Consult a pro for structural rot repairs, but you can tackle small ones yourself.
Instructions
Repair decayed wood
1. Use a wood chisel, an electric drill with a spade bit, or another tool appropriate for the situation to remove all wet, loose and unsound wood.
2. Probe the surrounding area with an awl. If it feels as solid as unaffected areas, drill numerous closely spaced holes of 1/8-inch (3-mm) diameter in the wood and inject a liquid wood hardener as directed by the manufacturer.
3. Mix two-part epoxy or polyester wood filler as directed. Mix only what you can apply and shape in a few minutes. Once the material hardens--and it does so quickly--you must throw it away.
4. Fill the hole or build up the affected area with the wood filler, using a putty knife or flexible plastic spreader (see A). Press hard to work the initial layer into the surface for a good bond.
5. Clean off the applicator and mixing container immediately.
6. Use a rasp tool to roughly shape or level excess filler as soon as the filler sets up, but before it dries completely (see B).
7. Use medium or coarse sandpaper to further shape and blend the patch when the filler is completely dry. On flat surfaces, use a rubber sanding block or power sander. On contoured surfaces, use wood dowels or other appropriate shapes to back the sandpaper.
8. Blow off the dust and apply freshly mixed filler to fill any remaining depressions or pinholes, or to build up more material as needed to attain the desired shape.
9. Use medium, then fine sandpaper to smooth the patch and feather it into the surrounding wood.
10. Touch up the patched area with primer and paint.
Take preventive steps
11. Use naturally decay-resistant or treated lumber for decks and other outdoor structures. Never allow untreated lumber posts or lumber to rest directly on concrete.
12. Clean joints between deck boards or between a deck and a house so debris and dirt won't retain moisture.
13. Inspect for peeling paint or other paint failures, especially near joints, such as mitered trim corners at roof eaves or where window and door casings contact sills.
14. Probe these areas with an awl to search for soft or wet, spongy wood (wood that resists being probed is sound).
15. Seal cracks with caulk. If possible, use screws to close any open miter joints. Bore pilot holes for the screws to avoid splitting the wood, and then inject adhesive caulk into the joint before driving in the screws.
16. Sand any bare wood and apply wood preservative before you apply a primer. Caulk joints after priming and before the top coating. Preservative greatly increases the likelihood of a better, longer-lasting paint bond.
17.Create ventilation through trimmed posts or columns by providing space for air to circulate between the trim and the floor surface and an outlet vent at the top. In some cases, this requires cutting 1/2 inch (12 mm) off the bottom of the trim. Lay a board that's 1/2-inch (12-mm) thick on the floor against the post and rest a handsaw on the board as you make the cut. Use small metal louvers pressed into drilled holes to vent the tops of posts or columns.
18. Avoid positioning outdoor sheds, such as one for trash cans, against wood siding. Elevate sheds above the ground on concrete blocks or short sections of 6-by-6-inch (15-by-15-cm) pressure-treated posts.
19. Make sure crawl-space vents remain open, especially during the summer, or add vents where there are none.
Related posts
Wood fillers help to protect and strengthen the inside of rotten wood.Treating wood to add strength and longevity are two of the most important parts of a reconstruction project. Using the best wo...
Repair and Repaint StuccoStucco is a decorative surface made from a mixture of aggregate, binder and water. It is a versatile material that can be easily shaped and applied when it is in its wet f...
You thought you had the problem resolved when you hired a contractor to paint your wood siding. But, days after the contractor is finished you notice that your new paint job is bubbling and peelin...
Stripping loose and peeling paint off a backyard deck can be a slow, hard, daunting job if you're just taking a metal paint scraper to it. Using chemicals to do it can create issues for the surrou...
Whether you have inherited a fence that has been covered with spray paint, or you accidentally sprayed your wood fence while involved in another project, there are a number of ways to remove it. U...
