spray paint vinyl or simulated leather
Believe it or not, there will be times in your life when you will have the need to restore faded vinyl color. This is common for boat seats, vehicle dashboards and upholstery. You could always go the route of re-upholstering the Vinyl, but I have done both and I prefer to just repaint it as long as the vinyl is in good structural shape and does not have any holes or tears. Here is how you restore Vinyl by painting it.
Instructions
1. The first step is to remove the Vinyl or simulated leather seat, dashboard, furniture, luggage, car door panel, vinyl car top, floor mats or other vinyl object to be restored from the vehicle, boat, home or whatever it is attached to. You do not want to actually remove the Vinyl itself, but the whole object it is attached to.
2. The next step is to remove any additional items from the object to be painted that you do not want to paint, such as switches, trim, knobs, screws, metal pieces, etc. If you do not have anything attached to your vinyl object to be painted, move on to the next step.
3. You want to place your vinyl or simulated leather object to be
re-painted and restored in a well-ventilated, dust-free area such as an open garage or workshop. It is recommended to place the object on top of a painters drop cloth, and to drape the drop cloth over anything that you do not want to be painted in order to catch an over-spray.
4. Now that you have you object set up in your painting studio or shop, you have removed the items from your vinyl object that you did not want to paint, such as metal trim, knobs, switches, etc - we need to clean all of the vinyl or simulated surfaces. Take some mild detergent and mix up a solution of 3/4 cup of soap to 4 parts water in your 5 gallon bucket. Take your sponge and thoroughly clean all of the surface area that you will be painting.
5. Rinse all of the soap residue off of your vinyl or simulated object to paint and let it dry. Use a dry, lint-free towel to help remove any excess water.
6. Allow the object to be painted to dry for at least 2-3 hours.
7. Now we want to take our blue painter' s tape and tape over anything that we do not want to get painted and which you could not remove in Step 2, such as metal framing, wires, etc. If you are painting a seat, you can tape over the metal parts or electronic switch housing, if you are painting a car door, you can tape over the door handles, etc. Careful preparation is key to keeping the paint where you want it, and this step should not be rushed. Take your time!
8. NOW WE ARE READY TO PAINT! This is where we will take our Rust-Oleum Vinyl spray paint and tack-cloth, and get ready to get down to business. I recommend the Rust-Oleum Vinyl spray paint because it actually contains vinyl in the paint to allow for the best adhesion and for maximum flexibility of the paint on the object. It will not crack, tear, or flake off when applied correctly to a clean dry surface. DupliColor is also another great choice to use!
9. Gently dust over your object to be painted to with your tack-cloth to remove any small dust particles. Be sure to only paint in temperatures between 50 degrees Fahrenheit and 90 degrees Fahrenheit with a humidity below 85% to ensure proper drying. Do not paint in windy, dusty conditions either, as it will screw up your paint job and include particles of dust, grass, insects, etc. into your final coat.
10. Shake the can vigorously for about a minute to get the marble inside to rattle (hence the term rattle-can painting). Hold the can 10-12" from the surface of the object and spray on a THIN first coat in a steady back-and-forth motion. You want to slightly overlap each stroke, and always keep your can the same distance from the object throughout the entire application of paint. You want to keep the first layer thin, almost transparent so that there are NO DRIPS and NO RUNS. If you get drips or runs, clean the nozzle tip, move further away from the object you are painting, and immediately wipe the drips and runs off with your towel.
11. After you have applied a nice, thin, almost transparent base coat, and allowed at least 15-30 minutes of time to dry. Go ahead and apply at least 3-5 more light coats until you can no longer see the original faded color, and you have a nice clean uniform new color. Remember to keep each coat light so that it will dry faster, and so that it does not drip or run.
12. Once you are finished painting your vinyl or simulated leather object, and you have allowed enough time for it to dry, turn your paint can upside down and spray it for 3 seconds to clean the nozzles. You can also use mineral spirits to wipe it off or any over-spray that you may have left on metal pieces, etc.
13. Now that you are done, we want to add a nice even coat or vinyl or simulated leather protection to the object you just painted. This will help to prevent fading and wear and tear. Use Armor-All protective wipes or spray.
14. Re-install your vinyl or simulated leather seat, dashboard, door-panel, whatever - and admire your handi-work.
Related posts
Make sure the roof is clean before you begin painting.Spray painting a metal roof can reduce glare, provide a layer of protection and change the appearance of a building. Factories, barns and ware...
Painting vinyl siding on your home or other structure can be done successfully, but you will need to prepare the vinyl for the paint to properly bond and last over the long haul. Vinyl siding expa...
If you want to improve the appearance of your vehicle, one of the simplest and most noticeable ways to do so is by getting a new paint job. Having a new paint job professionally done for your car...
Spruce up your car's interior.One cup of spilled coffee can be disastrous to your car's upholstery. Getting the seats in your car reupholstered may not be in your budget. If you can afford a can o...
White vinyl siding can be difficult to paint because it contracts and expands depending on the weather. Because of this, the paint can chip and break off if applied improperly. All the work you pu...
